Accessories for electronic locks
Locking part 74
The LATCH74 strike plate is used as a counterpart for SOLO and TEN hinged doors and drawers.
They are mounted on the side of hinged doors, drawers or on the top bar of drawers.
- Adjustable in height/width/depth
- Automatic adjustment +/- 2 mm
- Ejector with 5.4 N spring force
- Predetermined breaking point of 25 kg
Doors and light drawers can be opened without handles and without locking.
Locking part 75
The LATCH75 strike plate is mainly used with the SOLO, TEN and BEETLE for sliding doors or when the SOLO or BEETLE is mounted on the carcase.
- Automatic adjustment +/- 2 mm
- Predetermined breaking point of 25 kg
- Adjustable in one direction during installation
Battery
The BATTERY CR123A is used to power the electronic furniture locks in the following product families:
SOLO, TEN, PLUR and PAD.
When the battery reaches the end of its service life, a continuous tone sounds for 15 seconds when the lock is opened and the lock no longer locks from that moment on.
The TEN lock displays a light signal and the lock no longer locks after opening.
- Do not use in combination with direct power supply
- Lifetime:
125 KHz: 5-9 years
13.56 MHz: 4-6 years
Bluetooth: 3-4 years
In continuous operation, a battery works for up to 20,000 cycles.
Replace the battery every 3 years if possible.
We can only guarantee this battery performance with the Panasonic CR123A 3V battery.
A minimum distance of 10 cm between two RFID locks must be maintained as soon as the battery is inserted.
Glass mounting set
The GLASSKIT is used for mounting on glass furniture in combination with the SOLO product family.
Tensile load:
- Up to 45 kg for hinged doors
- Up to 25 kg for sliding doors
They are mounted directly onto the cleaned glass surface using the adhesive film supplied.
The cover film is attached to the outside.
Latch 74 glass mounting set
The Latch74 Glass is used for mounting on glass furniture in combination with the LATCH74 locking part.
- Up to 45 kg for hinged doors
They are mounted directly onto the cleaned glass surface using the adhesive film supplied. The cover film is attached to the outside.
Metal mounting set
The METAL KIT is used for mounting on metal furniture in combination with the SOLO product family.
- Metal cut-out: 42×42 cm
The screws supplied are suitable for metal thicknesses of 0.5-2 mm for screwing the cover plate to the lock.
Programming card
The programming card is used to activate and deactivate key cards, key fobs, RFID stickers, wristbands or other RFID keys.
- One programming card is used for countless locks
- The programming card is activated by pressing the button on the back of the lock (see programming instructions)
- Only one programming card per lock can be active at any one time.
Key card
The KEYCARD is used as a key for RFID locks.
- Waterproof
- Credit card format
Key fob D
This KEYFOB is used as a key for 125 KHz locks.
- Waterproof
- Metal surround
- Glossy black key fob
Key fob
The KEYFOB is used as a key for RFID locks.
- Waterproof
- Key fob black/white
Key-fob
The KEYSTICKER 125 is used as a key for 125 KHz locks.
This RFID sticker can be attached to existing cards or operating devices.
Properties:
- Particularly suitable for mounting on plastic
- 3M adhesive film with 0.3 mm thickness
- Round version: 30 mm Ø
- Rectangular version: 30×19 mm
- Special sizes on request
External antenna 125
If the SOLO or PLUR lock with 125 KHz is difficult to access, this antenna is plugged into the lock to make it easier to use.
- Wooden furniture: mounted on the inside, not visible from the outside
- Metal furniture: mounted visibly from the outside
- Cable length: 1.5 m
- EM4102/ EM4200 RFID Technology
Extra antenna 125 round
If the square external antenna is too large, this small round antenna can be used.
Due to the small diameter, the antenna should be lowered as far as possible to the surface.
- Wooden furniture: mounted on the inside, not visible from the outside
- Cable length: 1.5 m
- EM4102/ EM4200 RFID Technology
External transformer
The transformer is a direct power supply for the SOLO and PLUR lock and is connected to the back of the lock using the 1.5 m cable.
- EU plug 220 V
- US plug 110 V
- Do not use in combination with batteries
- Up to 5 connected locks can be operated with one transformer
A spacer plate is suitable in combination with the SOLO lock.
Distance plate
The spacer plate serves as protection for the cables when a SOLO is used with a transformer, SOLO SECONDARY or an external antenna.
Connection cable
The connection cable serves as a connection between SOLO and SOLO SECONDARY locks.
Battery AAA
The BATTERY AAA is used to power electronic furniture locks in the QUAD product family.
When the battery reaches the end of its service life, a continuous tone sounds for 15 seconds when the furniture is opened.
The lock no longer locks from that moment on.
- Do not use in combination with direct power supply
- Lifetime:
125 KHz: 5-9 years
13.56 MHz: 4-6 years
Bluetooth: 3-4 years
In continuous operation, the batteries function for up to 25,000 cycles.
Replace the batteries every 3 years if possible.
Plug-in distributor
The plug-in distributor is a slot extension for applications such as the SOLO with SOLO SECONDARY locks.
It is also used when several BEETLE SECONDARY locks are operated together.
Update: Gym
With the GYM update, any free locker can be occupied with any RFID key (card/chip).
Only the key used to close the lock or the programming card, which serves as the master, can open the lock again.
After opening, the locker can be occupied by any RFID key.
Properties:
- Ideal for use in public areas, fitness studios or staff lockers.
- The GYM update is only compatible with SOLO 125+/SOLO 13+ locks
- The locker can only be occupied when the door is closed and an RFID key is stopped.
- Several lockers can also be assigned with one RFID key.
- When not installed, the lock can be tested with the locking part inserted.
The GYM update can either be installed automatically on SOLO 125+/SOLO 13+ locks at a later date using the UPDATECARD GYM ON or the locks can be ordered in advance with the update installed.
Update: Alarm
If the furniture is not closed within 25 seconds, a continuous tone sounds as an alarm.
Applications:
- Ideal for securing goods in stores
- Securing medicines and spirits
Stopping an active RFID key or closing the door extinguishes the signal.
Update: Bolt
With this update, the lock does not lock automatically after 3 seconds but remains open until the key is stopped again.
When using several locks in a group (wired), this bolt function may only be used with one transformer.